AIM SOLUTION

 

Electronics for retrofitting – Automatically record digital cable ID

AIM - Automated Infrastructure Management

Intelligent patching and real-time monitoring with FUTURE-PATCH for patch panels in large networks

Automated management and administration of network infrastructure is becoming important more and more. Unwanted situations can only be minimised by keeping uniform and standardised processes - optimally they are additionally automated. According to a study by Gartner, the root cause for about 30% of all network failures can be found in the cabling or the physical connection.

In order to contribute improving this situation, we offer an intelligent system that monitors the connection of the physical network layer. The area of high port density, e.g. in the network racks in data centers is the point where the solution comes in. We recommend to equip the entire patch panels with intelligent electronic and use intelligent patch cords in order to keep an eye on the real-time monitoring of the port states. A PCU (Panel Control Unit) is equipped at the front of the patch panels and scans the area in front of each port. If a connector of an intelligent patch cord is now connected with the patch panels port, the cable ID is recognized. The second side of the patch cord has the same cable ID and when the cable ID is now detected on both ports, the cable link is automatically recognized and also documented in the DCIM (Data Centre Infrastructure Management) software. If the actual state in front of a patch panel changes (e.g. based on the removal of an intelligent patch cord) and the target state (last authorised state in the DCIM software) describes something different, a warning report is automatically been published.

 

 

Scalable

The system is designed for any network size, whether for 1,000 or 100,000 ports

Intelligent

Push notifications are sent automatically - Intelligent detection of cable types

Documented

Real-time monitoring of the physical connection with simultaneous documentation

Automatic

Automatic recording of all "Moves, Adds and Changes" and thus minimisation of errors in the documentation

Network Security - Reliability - Uptime

In order to meet the ever-increasing demands for fail-safety and reliability, the basis of an entire network must be able to exchange data safely and error-free at all times. To ensure this, the physical network layer must always and without exception be reliably connected correctly. This can often only be achieved through standardized processes that automatically detect changes and also document them correctly in the long term. Immediate alerts to mobile devices in the situation of unauthorised changes ensure that recovery times are minimised.

When planning changes, it is invaluable if the basis of the planning (target state) - the documentation - also corresponds exactly to the real cabling (actual state). In this way, situations can be avoided right from the start where technicians on site have to make enquiries to the IT administration because their change orders cannot be carried out, e.g. because the new port to be connected to is not free and the risk is too high to remove the unexpectedly existing patch cord because it is not clear what will happen then - there is no documentation about it. In the best case, a time-consuming and costly investigation for the cause begins.

To meet the high demands of today and the even greater demands of tomorrow, we recommend investing in an AIM system such as FUTURE-PATCH, because at the end of the day this saves time and money.

How does FUTURE-PATCH work as part of a DCIM solution?

One component of a DCIM solution is the management of the physical network layer. This is where FUTURE-PATCH comes in and enables complete monitoring of the patching area in network racks. The real-time monitoring of all actual port states is realised by intelligent electronics placed on the front of the patch panels. The database of the DCIM software shows the target state in each case - if there is a difference between the two states, a message is generated in real time and the point of failure can be determined immediately. The unique advantage of such a solution is the knowledge of all states at the patch panel ports of the entire physical layer in the network. According to the Gartner study, where 30% of all network failures are due to the cabling or physical connections, this root cause of failure can be minimised.

FUTURE-PATCH is therefore an intelligent, electronics based solution that allows technicians to be visually guided (LED) on site at the rack when adding or removing patch cords and to directly check the correctness of the work. Furthermore, it is the building block in an intelligently monitored network, which permanently monitors the physical state of the patch panel ports and immediately informs by message in case of unwanted states.

Product groups and variants

The FUTURE-PATCH system is now in its 2nd generation and offers several variants per product group in some cases.

 
Intelligent Patch Panel Systems
 

Generation 2 - Intelligent Patch Panel System - V2

  • PCU - Panel Control Unit - intelligent electronics for patch panels - More ...
  • Patch panel AIMready for retrofitting with PCU - More ...
  • Intelligent patch cords with RFID transponder factory made - More ...
 
The Rack Management
 

RCU - Rack Control Unit

  • Rack Control Unit - 19inch - 1,0 U - with text display - More ...
  • Rack Control Unit - Compact - 0,0 U - without text display - More ...

Bus system

  • Bus cable - bus connector - bus termination - crimping tool - More ...
 
DCIM - Third Party Software
 

DCIM - Software:

  • AT+C VM.7 - Connecting Manager - More ...
  • PATCH MANAGER - Infrastructure Management Software - More ...

Advatanges

  1. Automatic documentation of connectivity
  2. Real-time monitoring
  3. Integration in superordinated DCIM solution
  4. Automatic push notification for unauthorised changes
  5. LED spot light for new connections
  6. LED warning light for faulty connections

Core elements generation 2 - PCUs and intelligent patch cords

PCU - PANEL CONTROL UNIT - V2
GENERATION PROVEN OVER MANY YEARS OF PATCH PANEL ELECTRONICS

The PCU of generation 2 is a two-part intelligent electronics for patch panels. It consists of an antenna unit and an electronic unit. The antenna unit is located directly above the port row at the front of the patch panel and the electronic unit is placed at the rear side of the patch panel. The bus system runs along the back of the panels. A tool-free way of retrofitting the PCU ensures quick installation and commissioning.

INTELLIGENT PATCH CORDS - LCDX - SCDX - RJ45 - V2
PATCH CORDS WITH CLIPS AND INTEGRATED TRANSPONDERS

The patch cords for generation 2 are fully factory assembled and programmed. As intelligent patch cords, they represent a combination product that offers connectivity at the highest level and at the same time the patch cord carries its individual characteristics stored in the transponder. The cable ID as well as the type of connector, the connection medium and the length can be read out directly depending on the type of DCIM software.

PCU and AIM ready Panel - V2

All Panel Control Units and the compatible 19 inch patch panels type AIMready of generation 2 can be found directly here:

IPC - intelligent Patch Cords - V2

All intelligent patch cords of generation 2 for copper and fiber networks can be found directly here:

Core elements Rack Management

RCU - RACK CONTROL UNIT
THE RACK MANAGER IN THE NETWORK

The entire system consists of a rack control unit, which is typically used per rack, and the PCUs located in this rack on its bus system. The RCU is a type of an interface - it organises the power supply and communication with the PCUs via the bus system at the lower communication level, while communication at the upper level takes place directly to a network switch via a network protocol. More ...

BUS SYSTEM
LINKING THE PCUS TO THE RCU

The bus system is the power supply and communication system of all FUTURE-PATCH products. It consists of a ribbon cable with bus terminators at both ends, and typically the RCU near one end of the cable, followed by all PCUs. A typical bus system solution within a full network rack would have the RCU at the top of the rack with all PCUs equipped on the patch panels below on the bus, which runs to the bottom of the rack. More ...

Third party elements Management Software

DCIM - SOFTWARE
DATA CENTER INFRASTRUKTUR MANAGEMENT

A DCIM solution (Data Center Infrastructure Management) usually offers three functional blocks for the management:
1) the entire infrastructure of a data centre
2) the fiber network outside the buildings
3) the office network and building infrastructure
In particular, these include managing the hall space, free space in racks, power and climate management and the end-to-end connectivity. For fiber optic networks outside the building, it is the management of the entire physical layer including a map management with GIS (geo information system). For office networks, it includes inventory management, a work order system and the entire process for "moves, adds and changes".

 
All available single components for the FUTURE-PATCH system
 

View as

9 Items

12
  • 12
  • 24
  • 36
per page
Filters
  • Position
  • Product Name
Product Name
  1. AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OM3-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    Add to Compare
    24, 18, 12, 06
    LCdx, SCdx
    HS, GB, GC
    9005
    SKU#: AP2-XXXXAQ-XXXPC-G0-9005 AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OM3-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    The pre-assembled AIMready TKM FO patch panels are direct applicable to use in FO networks. They are usable as patch panel ready to splice with already implemented splice equipment (PPRS - Patch Panel Ready to Splice). The AIMready patch panel are realised for a tool-less retrofitability of an AIM antenna kit.
  2. AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OM4-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    Add to Compare
    24, 18, 12, 06
    LCdx, SCdx
    HS, GB, GC
    9005
    SKU#: AP2-XXXXHV-XXXPC-G0-9005 AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OM4-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    The pre-assembled AIMready TKM FO patch panels are direct applicable to use in FO networks. They are usable as patch panel ready to splice with already implemented splice equipment (PPRS - Patch Panel Ready to Splice). The AIMready patch panel are realised for a tool-less retrofitability of an AIM antenna kit.
  3. AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OM5-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    Add to Compare
    24, 18, 12, 06
    LCdx, SCdx
    HS, GB, GC
    9005
    SKU#: AP2-XXXXLG-XXXPC-G0-9005 AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OM5-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    The pre-assembled AIMready TKM FO patch panels are direct applicable to use in FO networks. They are usable as patch panel ready to splice with already implemented splice equipment (PPRS - Patch Panel Ready to Splice). The AIMready patch panel are realised for a tool-less retrofitability of an AIM antenna kit.
  4. AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OS2-APC8 - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    Add to Compare
    24, 18, 12, 06
    LCdx, SCdx
    HS, GB, GC
    9005
    SKU#: AP2-XXXXGN-XXXA8-G0-9005 AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OS2-APC8 - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    The pre-assembled AIMready TKM FO patch panels are direct applicable to use in FO networks. They are usable as patch panel ready to splice with already implemented splice equipment (PPRS - Patch Panel Ready to Splice). The AIMready patch panel are realised for a tool-less retrofitability of an AIM antenna kit.
  5. AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OS2-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    Add to Compare
    24, 18, 12, 06
    LCdx, SCdx
    HS, GB, GC
    9005
    SKU#: AP2-XXXXBL-XXXPC-G0-9005 AIMready FO Patch Panel - Compact - 1U - PPRS-EX-AL - [XX]x [XX] - OS2-PC - splice equipment: SE: [XX] - SP: [XX] - RAL 9005
    The pre-assembled AIMready TKM FO patch panels are direct applicable to use in FO networks. They are usable as patch panel ready to splice with already implemented splice equipment (PPRS - Patch Panel Ready to Splice). The AIMready patch panel are realised for a tool-less retrofitability of an AIM antenna kit.
  6. FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx - LCdx - 2G50/125 OM3 - incl. RFID transponder - length [m]: [XXX]
    Add to Compare
    READY
    V2
    LCdx
    HS
    SKU#: 51700963FP-XXX-OM3 FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx - LCdx - 2G50/125 OM3 - incl. RFID transponder - length [m]: [XXX]

    The AIM system FUTURE-PATCH is part of a ultra modern DCIM solution for managing complex IT infrastructure. The physical status of all patch panel ports is monitored and managed in real time with this system. The intelligent patch cords - iPCs - are factory made and equipped with transponder and digital cable ID.

  7. FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx - LCdx - 2G50/125 OM4 - incl. RFID transponder - length [m]: [XXX]
    Add to Compare
    READY
    V2
    LCdx
    HS
    SKU#: 51700963FP-XXX-OM4 FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx - LCdx - 2G50/125 OM4 - incl. RFID transponder - length [m]: [XXX]

    The AIM system FUTURE-PATCH is part of a ultra modern DCIM solution for managing complex IT infrastructure. The physical status of all patch panel ports is monitored and managed in real time with this system. The intelligent patch cords - iPCs - are factory made and equipped with transponder and digital cable ID.

  8. FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx-APC8 - LCdx-APC8 - 2E9/125 OS2 - incl. RFID transponder - length [m]: [XXX]
    Add to Compare
    EQUIPPED
    V2
    LCdx
    HS
    SKU#: 51701341FP-XXX FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx-APC8 - LCdx-APC8 - 2E9/125 OS2 - incl. RFID transponder - length [m]: [XXX]

    The AIM system FUTURE-PATCH is part of a ultra modern DCIM solution for managing complex IT infrastructure. The physical status of all patch panel ports is monitored and managed in real time with this system. The intelligent patch cords - iPCs - are factory made and equipped with transponder and digital cable ID.

  9. FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx-PC - LCdx-PC - 2E9/125 OS2 - incl. RFID transponder - length [m]: [XXX]
    Add to Compare
    READY
    V2
    LCdx
    HS
    SKU#: 51700974FP-XXX FUTURE-PATCH - FO - intelligent patch cord V2 - iPCs: LCdx-PC - LCdx-PC - 2E9/125 OS2 - incl. RFID transponder - length [m]: [XXX]

    The AIM system FUTURE-PATCH is part of a ultra modern DCIM solution for managing complex IT infrastructure. The physical status of all patch panel ports is monitored and managed in real time with this system. The intelligent patch cords - iPCs - are factory made and equipped with transponder and digital cable ID.

View as

9 Items

12
  • 12
  • 24
  • 36
per page
Filters
  • Position
  • Product Name
Product Name
Copyright © 2021-2024 · TKM GmbH · Alle Rechte reserviert.